airporthospitalsindustrylogisticsretailArtboardempowermentAsset 1Asset 2innovationbrochureGroup 11productpassionproductsrespectAsset 3Combined ShapeteamworkArtboard@2xGroup 11whitepaperwiring-diagramsi-access-controli-artwork-protectioni-automated-windowsi-barrier-freei-barriersi-bus-doorsfooi-crosswalki-emergency-calli-escalatorsi-flammablei-gatesi-guidancei-high-performance@1x-100i-knowing-acti-loading-docki-low-energy-doorfooi-parkingi-pass-through-windowi-people-countingi-perimeter-protectioni-plateform-screen-doori-request-to-exiti-revolving-doori-sectional-doorAsset 3i-sliding-doorsi-swinging-doorsi-toll-gatesi-train-doorsi-vehicle-classificationi-warehousingfacebookinstagramlinkedintwitteryoutubearrowarrow-redux-bigarrow-redux-toparrow-redux-toparrow-reduxarrowArtboard@2xcountrydownloadeyefile2filtergridhamburgerlanguagelistnopdfphoneplusresetsearchsubscribevideoyesArtboard@2x

We've detected you are coming from another region. Please choose one of the options:

Please select your preferred market and language


IXIO-DT1 Industrial



BEA’s dual technology IXIO-DT1 Industrial is the premier activation and safety sensor on the market.

The IXIO-DT1 Industrial is a highly flexible and user-friendly solution for interior industrial doors, vehicle gate detection and off-door automation.

This cutting-edge sensor has earned an impressive list of credentials and certifications, including UL, FCC and IP54.


Highly adjustable

Ten microwave activation sensitivity settings and three infrared safety immunity settings

Precise presence detection

Two 24-spot, high-density, infrared safety curtains providing precise presence detection

Standards compliant

Fully monitored internally, capable of external monitoring

Easily adjustable

Four visible red alignment spots are projected on the ground to assist in precise IR curtain adjustment

Table of specifications


Microwave Doppler Radar

Active Infrared

Detection Mode



Transmitter Frequency

24.150 GHz


Transmitter Radiated Power

< 20 dBm EIRP


Transmitter Power Density

< 5 mW / cm2


Spot Size


2 in × 2 in

Max. Number of Spots


24 per curtain

Max. Number of Curtains



Max. Contact Voltage
Max. Contact Current
Hold Time

Electro-mechanical-relay (potential and polarity free)
30 VDC
1 A
Microwave: 0.5 – 9 s (user adjustable)

Solid-state-relay (potential and polarity free)
42 VDC
400 mA
Infrared: 0.3 – 1 s

Test Input


Sensitivity: Low: < 1 V; High: > 10 V (max. 30 V)
Response time on test request: typical: < 5 ms

Supply Voltage

12 – 24 VAC ±10%; 12 – 30 VDC ±10% (to be operated from SELV compatible power supplies only)


Power Consumption

< 2.5 W


Mounting Height

78 in – 138 in (6.5 ft – 11.5 ft)


Temperature Range

−13 °F – 131 °F
0 – 95% relative humidity, non-condensing


Degree of Protection



Norm Conformance

R&TTE 1999 / 5 / EC; EMC 2004 / 108 / EC;
MD 2006 / 42 / EC; RoHS 2002 / 95 / EC



10.6 in (W) × 2.27 in (H) × 2.25 in (D)


Cable Length

360 in (30 ft)

  • ixio-dt1_st

    Activation and safety sensor for interior industrial doors

Frequently asked questions

Why will the IXIO’s active infrared safety pattern not hold the door open?

The brown and blue wires must be connected, or F1 must be set to “1” using the remote control.


Why is the PNP harness not working on a BESAM control?

The harness is reversed; the short harness plugs into the IXIO.


Why is the RECORD sliding door holding open?

The RECORD control uses a normally closed safety circuit; set the safety output to N.C.


Why is the IXIO bliking red on a DORMA door?

The IXIO is defaulted to monitoring ON; connect the two (2) purple monitoring wires to the control.


How do I eliminate four (4) orange LED flashes or “low AIR”?

Verify the pattern width shutters are not closed (the software should still be set to wide).Verify the active infrared safety pattern is not tilted out too far away from the door.

Turn off the 2nd active infrared safety pattern row.


Why does the door recycle open?

If the red LED illuminates, the active infrared safety curtain needs adjusted.

If the green LED illuminates, the microwave activation angle/sensitivity/immunity needs adjusted.


What are the extra wires not connected to the door control?

The two (2) purple wires are for monitoring and the yellow wire is for N.C. activation relay.


How do I locate the IXIO’s active infrared safety pattern relative to the door face?

Double-click the gray knob to turn on the visible red aligment spots or press UNLOCK > MAGIC WAND > + on the remote control, and then use the red knob to adjust active infrared saftey pattern to within 3” of the face of the sliding door panel. After adjustment, relaunch a setup.


How do I use an IXIO for 1-way traffic reactivation?

If the door is equipped with a two-way traffic option, connect the white and green wires to the activation circuit.

If the door is NOT equipped with a two-way traffic option, DO NOT connect the white and green wires to the activation circuit; instead, connect the brown and blue wires to the safety circuit.

Using the LCD, set RAD: REENTRY to value “”3″” or “”4″”. Walk-test to ensure there is a minimum of a 24” reactivation zone.


Why does the IXIO LED blink fast red when I try to unlock it with the remote control?

A lock code has been entered. To remove it, power cycle the IXIO and then press UNLOCK > LOCK > 0000.


See all our products